Exhaust Gas Extraction in Truck Repair Shops: Operational Requirements
In maintenance and repair shops, trucks and other commercial vehicles may be operated with the engine running during diagnostics, testing, or maintenance. This results in diesel exhaust being emitted directly into the work area.
Exhaust extraction systems for trucks should therefore be installed as close as possible to the exhaust outlet. The goal is to capture the emissions before they spread throughout the workshop. This is particularly important for protecting employees’ health, especially when engines are running regularly. Employees often work directly on or under the vehicle and are thus in close proximity to the source of emissions. An effective extraction system helps reduce air pollution in the workshop and specifically removes diesel exhaust fumes from the work area.
Trucks and Passenger Cars: Differences in Exhaust Extraction
The basic principle is the same: exhaust gases should be captured as close as possible to the point of origin. However, the practical implementation differs.
For commercial vehicles, factors such as larger vehicle dimensions, varying exhaust positions, and longer work areas must be taken into account. Engine type and operating conditions can also influence the volume of air that must be safely captured.
In addition, commercial vehicle repair shops often service a wide variety of vehicles. In addition to standard trucks, for example, vans, municipal vehicles, or specialty vehicles may be serviced in the same facility. An exhaust extraction system in a commercial vehicle workshop should therefore not be designed for a single vehicle, but should take into account the actual fleet and typical workflows.
The Exhaust Position as a Key Planning Factor
The position of the exhaust outlet is one of the most important planning parameters for a truck exhaust extraction system.
Depending on the vehicle, the exhaust may be located on the side, at the rear of the vehicle, or higher up on the vehicle. Different body types or vehicle variants can also cause the extraction position to vary from vehicle to vehicle.
The extraction system must therefore be able to reach the relevant connection area without unnecessarily restricting maintenance work or traffic flow.
This means: The more varied the exhaust positions of the commercial vehicles serviced in a workshop are, the more flexibly the capture unit should be able to be positioned.
In our workshop solutions, we tailor the routing and positioning of the exhaust extraction system to the vehicle size, workstation, and movement areas. For commercial vehicle facilities, it is particularly important that exhaust gases are captured directly at the exhaust outlet and that the system interferes as little as possible with workshop operations.
Our systems for industry and workshops are modular in design and are adapted to the specific application. This ranges from a single workstation to a large commercial vehicle facility. We can also retrofit existing facilities with a suitable exhaust extraction system, provided the structural conditions are appropriate.
The focus is therefore not on a specific standard configuration, but on a solution that fits the vehicles, the facility’s layout, and operational processes. This is precisely what we focus on in our consulting and project planning .
Properly Accounting for Vehicle Size and Work Area
The larger dimensions of commercial vehicles change the requirements for the reach and positioning of the extraction system.
During the planning phase, the following should be clarified, among other things:
• which vehicle classes are serviced in the facility,
• how long and tall the vehicles are,
• where the exhaust outlets are located,
• how the vehicles are positioned at the workstations,
• whether multiple vehicle types will use the same workstation,
• and which movement and maintenance areas must remain clear.
This information determines how large the required working area of the extraction unit must be and which hose or rail routing is appropriate.
How much extraction capacity do commercial vehicles need?
When sizing an exhaust extraction system, it is not enough to simply distinguish between passenger cars and trucks. The required extraction capacity depends, among other things, on the engine, exhaust pipe, operating conditions, and the intended work. A vehicle idling has different requirements than an engine operating at elevated RPM during a test. Therefore, the required air volume should always be determined based on the specific application. A one-size-fits-all design based solely on vehicle class may fall short. We take such operating conditions into account when designing exhaust extraction systems .
From a single workstation to a large commercial vehicle facility
The appropriate design depends primarily on the workstation layout, vehicle mix, and use of the facility. To this end, we develop modular systems ranging from a single workshop station to a large-scale commercial vehicle facility.
A clearly defined single workstation has different requirements than multiple workstations used in parallel or changing vehicle positions. That is why, during planning, we always consider actual workshop operations and not just the vehicle type.
Depending on the requirements, the following system concepts may be appropriate, for example:
• Single-station systems for defined maintenance and inspection areas,
• semi-automatic solutions for recurring workflows,
• fully integrated systems for larger workshops and commercial vehicle facilities,
• as well as custom-designed systems for specific vehicle or facility situations.
It is crucial that the chosen solution reliably captures exhaust gases directly at the vehicle during actual operations and can be seamlessly integrated into the existing workshop.
Flexibly serving mixed commercial vehicle fleets
A truck repair shop often does not service a completely uniform fleet of vehicles. Different heights, wheelbases, body types, and exhaust positions place greater demands on the flexibility of the exhaust extraction system. Therefore, the entire relevant vehicle fleet should be considered during the planning phase whenever possible. This also includes vehicles that are serviced only occasionally, provided they use the same workstation. An exhaust extraction system for commercial vehicles should be designed so that the intended vehicle variants can be reliably connected without the need for costly retrofitting.
Health Protection Through Direct Exhaust Capture
Diesel exhaust should be captured as close as possible to where it is produced. This applies to passenger cars as well as trucks and other commercial vehicles. In large workshop facilities, general ventilation alone is not the same as direct exhaust capture. If emissions are captured directly at the exhaust, they do not enter the work area to the same extent in the first place. For employees who regularly work in the immediate vicinity of running commercial vehicles, this approach is a key component of health protection. We therefore place protection against harmful diesel exhaust at the center of our solutions for industry and workshops.
Planning Multiple Truck Workstations Together
When multiple commercial vehicles are serviced simultaneously, the exhaust extraction system must be tailored to the actual degree of simultaneous operation. Key factors include how many vehicles are running at the same time, how the workstations are arranged, and whether the extraction units must be operated independently of one another. With multiple workstations, therefore, the key is not so much a specific standard approach as it is a properly sized, modularly designed system. We tailor the number and arrangement of extraction points to the actual workshop workload and operational processes.
Retrofitting in Existing Truck Workshops
We offer exhaust extraction systems for both new workshops and for retrofitting existing commercial vehicle facilities. In existing facilities, however, the hall geometry, supporting structure, doors, lifting equipment, lighting, and other fixtures are already predetermined. The extraction technology must integrate into these structures.
Before retrofitting, we therefore assess which installation and movement areas are available, which workstations need to be reached, and how the extraction system can be integrated into the existing facility. A thorough site survey helps us develop a solution that is both technically sound and minimizes disruption to existing workflows.
The project planning requires the following information
The more detailed the information on the vehicles and workshop operations, the more precisely the system can be designed.
Before project planning, it is particularly important to document vehicle types, exhaust positions, engine operating conditions, the number and layout of workstations, and existing facility equipment.
It is also important to consider whether the types of vehicles might change in the future or whether additional types of commercial vehicles might be added. A certain degree of flexibility can simplify future adjustments.
Planningan Exhaust Extraction System for Trucks That Fits the Workshop
An exhaust extraction system for trucks must take into account the specific characteristics of commercial vehicles and their workshop operations. Vehicle size, exhaust position, work area, and operating conditions influence which extraction technology is most appropriate. While the principle of direct extraction remains the same for passenger cars and trucks, a commercial vehicle workshop often requires greater reach and more flexibility.
We develop suitable exhaust extraction systems for workshops, ranging from individual automotive workstations to large commercial vehicle facilities.
Plan an Exhaust Extraction System for Your Truck Workshop
Are you planning a new commercial vehicle workshop or looking to equip an existing facility with a suitable exhaust extraction system?
We’ll assist you in selecting and designing a suitable solution tailored to your requirements.